Computer assemble and attach the picture

Early Steps What should be done in preparing material is used to ..Tools and MaterialsTools:1. Screwdriver Plus (+)2. Screwdriver Minus (-)3. Thin Tang (GOES Crocodile)4. Multimeter / Multitester5. Tweezers6. Anti-Static BraceletMaterials along with an explanation:1. MotherboardThe motherboard is a motherboard or main circuit board in a computer, which contains an electronic circuit that serves as a processing center.2. ProcessorProcessor is a component of most computer key because it determines a good or bad performance of the computer (brain computer). Serves as a data processor in the computer system.Processor type that is often used in assembling pc / computer itself is good and right for the game and there are 2 common types Intel Pentium III, Pentium 4, dual core, quad core, Core i3, Core i5, Core i7 and AMD Sempron type , Athlon, Phenom up.3. The heatsink (fan)Heatsink fan is cooling the processor and other components, because the processor temperature is very hot.4. Hard DriveHard is a hardware component that stores data and provides magnetic disk. Serves as a data storage to improve computer performance.5. Memory (RAM)RAM (Random Access Memory) is the internal memory, which is used to store data.FDD is a storage device that serves to connect the data transfer, data reading or "write" data from the PC to a diskette.6. CD / DVD DriveCD / DVD ROM drive is a storage device that is used to connect data, data transfer, data reading or "write" data from the PC to a CD / Cassette7. Graphics Cards (VGA Card)Card VGA (Video Graphics Adapter) is a component that serves to translate the computer output to the monitor. For the graphic design or playing video games, card required high-powered graphics.8. Sound CardSound Card is a plate-shaped device that is capable of processing and PCB as well as generate noise. Duty to support the voice functions in a multimedia PC.9. Power SupplyPower Supply is a computer device that is used to supply power to any part of a computer in order to run.10. Casing11. Keyboard & Mouse
The following are steps that should be done in assembling Computer CPU:1. Place the motherboard on a flat place and do not forget to give your footwear with a soft surface such as a motherboard that steroporm not scratched or broken line components.


2. Put the processor on the motherboard. Installation processor earned outside the casing in order to facilitate installation in the processor. Installing the processor is adapted to the type of processor and motherboard use.Dont forget to check back at a later time after installed.

 3. After the processor is installed and then do the installation (PAN) processor fan.adjust to the type of 
motherboard and processor used
.

 4. Install the RAM RAM slot available on the motherboard. Installing RAM slots must follow the rules because if there is an error in the installation can create a RAM and motherboard damaged or too forced terbakar.dan do not go if the RAM ..

5. Prepare the chassis for the installation of all components that have been provided.
6. After setting casing attach the power supply as shown below.




7. After that, enter the motherboard in the chassis to the motherboard are slowly being damaged. At the time of installation of the motherboard, look at the mouse connector, keyboard, serial, VGA and sound that is attached to the panel on the casing properly.

8. Then screw the motherboard in order to stand strong and not rocking.9. In this example we are using a motherboard that is equipped with VGA, Sound Card, LAN card, and built into the motherboard. Components that have become one with the motherboard with components called ON BOARD.
10. After the install CD-ROM on a shelf on the casing, by entering from the front.
11. Then screw the CD ROM which had been attached to the shelf down with no shake. Then plug in the power cable and a data cable or cable ATA CD-ROM on the motherboard.12. Install the hard drive on the shelf on the casing with a slow hard drive in order not to hit. Because of this hard drive is prone toward shocks. Then screw tightly so as not to shake.


13. After the drive is installed and replace data cable or cable ATA hard drive on the motherboard and the hard disk itself.14. Connect the power supply in place contained in the motherboard. If the installation is wrong, it will result in fatal damage to the motherboard.
15. Then plug the power connector / restart / hdd lad / power connector pad lad and the other contained in the motherboard as shown below.
16. After all the components have been installed and then plug the casing cover properly.

Finish the assembly must then test whether we succeed or not. Plug the cable into a VGA monitor port and power to the CPU and monitor power switch, then turn it on when the computer can boot the assembly work. If you can not boot means the assembly is not perfect, it must be completed in advance if you want to later install the Operating System is a way to re-check all of the components that have been installed if it is correct or not.Hopefully this article useful